Now that you've finally got your hands on a Raspberry Pi, you're probably itching to make some fun embedded computer projects with it. What you need is an assembled add on prototyping Pi T-Cobbler from Adafruit, which can break out all those tasty power, GPIO, I2C and SPI pins from the 26 pin header onto a solderless breadboard. This mini kit will make "cobbling together" prototypes with the Pi super easy. Designed for Raspberry Pi Model B Revision 1 or Revision 2. This assembled Cobbler is in a fancy T-shape, which is not as compact, but is a little easier to read the labels. We also have the more compact original Cobbler. The assembled Pi T-Cobbler mini kit comes with a 26 pin ribbon cable, and an already soldered T-Cobbler as shown. No soldering required! This mini kit comes fully assembled! The PCB and header come soldered together so you can plug the cable between the Pi computer and the T-Cobbler breakout. The T-Cobbler can plug into any solderless breadboard (or even a prototyping board like the PermaProto). The T-Cobbler PCB has all the pins labeled nicely so you can go forth and build circuits without keeping a pin-out printout at your desk. We think this will make it more fun to expand the Pi and build custom circuitry with it. The Adafruit Pi T-Cobbler is compatible with both versions 1 and 2 of the Raspberry Pi Computer - for version 2 computers, note that the GPIO #21 has been replaced with GPIO #27 and that the I2C pins are now I2C port #1 instead of #0. All other pins are the same. Please note, this product only contains a 26 pin ribbon cable, a custom PCB with ribbon cable socket and header pins soldered to it. The Raspberry Pi, breadboard, breadboarding wires, cables, components, case, power supply, etc is not included! We do stock many of those items in the shop, so check those out as well!
Flora Wearable GPS Kit Operating Instructions (1.57MB) EN Get started with the fabulous Adafruit Flora platform with this lovely starter kit. Included are plenty of parts to make a few different fun projects! There's a Flora motherboard FLORA, WEARABLE GPS STARTER PACK Flora Wearable Ultimate GPS module Eight Flora RGB NeoPixels V2 3xAAA Battery holder with JST connector and on/off switch Stainless Thin Conductive Thread - 2 ply - 25 meter/85 ft Stainless Medium Conductive Thread - 3 ply - 18 meter/60 ft Needle set with 20 pieces Small Alligator Clip Test Lead (set of 12) USB cable - A/MiniB - 3ft 4x Alkaline AAA batteries 2x NPN Bipolar Transistors (PN2222) 2x Super-bright 5mm IR LEDs 2x Super-bright 5mm IR LEDs 2x 100-ohm resistors MSL: -
Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition to your robotic gardening project. There are two ½'' (Nominal NPT) outlets. Normally, the valve is closed. When 12Vdc is applied to the two terminals, the v... Plastic valve. Working pressure: 0.02Mpa-0.8Mpa. Weight: 122g.
The size of these buttons Self-timer, of just 5 mm, make them perfectly adaptable to allegations of Arduino Flora. These Automatic are an extremely comfortable connector for wearable projects: it firm a part to the card, and the other is staples with conductive thread. During the welding there could be a loss of colour due to the temperature. These buttons are washable, resistant to oxidation, and non magnetic.
LED Sequins - Ruby Red 5pk element14 Technical Page (374.93KB) EN Manufacturer Product Page (69.45KB) EN Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel WEARABLE LED SEQUINS, RUBY RED, 5PK
This TowerPro servo can rotate approximately 180° (90° in both directions). It is great for beginers wanting to make projects without building a full motor controller with gear box. It has been specifically designed for RC cars and planes but can be used f... Average speed (4.8V): 0.12sec/ 60°.
All-original DIY electronics - Adafruit Industries is a New York City based company that creates open source hardware and parts for original electronics projects featured on www.adafruit.com as well as other cool open source tronix' that we think are interesting and well-made.Kindle blogs are fully downloaded onto your Kindle so you can read them even when you're not wirelessly connected. And unlike RSS readers which often only provide headlines, blogs on Kindle give you full text content and images, and are updated wirelessly throughout the day.
Move fluid safely from here to there with this very nice little pump. Unlike most liquid pumps, this is a peristaltic type - the pump squishes the silicone tubing that contains the liquid instead of impelling it directly. The upshot? The pump never touches... Uses 3/16'' (4.7mm) outer diameter silicone tubing. Working Temperature: 0°C - 40 °C. Weight: 200 grams. Dimensions: 27mm diameter motor, 62mm total length. Mounting holes: 3mm diameter, 5mm center-to-center distance. Supplied with x2 half meter silcone tube attached unsterlized.