Alliance Remedial Supplies

BASEMENT TANKING CAVITY DRAIN MEMBRANE DAMP PROOF KIT 2M X 20M (40M2)
Alliance Remedial Supplies
£160.00
Cavity Drain Clear Tanking Membrane Kit 8mm Stud 2mtrs x 20mtrs (40m2) Suitable for waterproofing and damp proofing walls and floors in basement conversions and new build projects. Contents of kit: 1 x roll of Cavity Drain HDPE membrane clear with an 8mm stud profile, 2mtrs wide x 20mtrs long (40m2) 1 x box of 100 Brick Plug Fixings with Seals which accommodate a 2″ size 10 screw for batten fixing (if batten fixing off membrane you will need to order a separate box of 100 plug fixings as 200 fixings will be required for a 40m2 area) 1 x roll Double sided sealing Tape 30mm wide x 22.5mtrs long Used by damp proofing and basement waterproofing contractors, Plastering contractors, Builders and DIY. This is a high quality strong durable HDPE cavity drain membrane with a stud profile of 8mm. The 8mm stud height minimises problems caused by raised floor levels. The membrane is highly versatile and can also be used in conjunction with thermal insulation, sound insulation and most types of under floor heating. This product is guaranteed for 20 years and has a life expectancy of at least 50 years (DIN 9001:2000). This membrane is an inert product with high compressive loading stability. It is highly resistant to water, alkalis, saline solutions and organic acids, and is not affected by minerals. It is also resistant to bacteria, fungi and other small organisms. Requires Brick Plug Fixings with a suitable waterproofing detail around the head of the plug if being used in a basement waterproofing installation. Used by damp proofing contractors, Plastering contractors, Builders and DIY.
Helical Bar Reinforcement Repair Kit With Polyester Resin Tubes x 3 Applicator Gun Mixer Nozzles x 3 Helical Bars x 5 by Alliance Remedial Supplies
Alliance Remedial Supplies
£77.11
Helical bar crack repair kit with polyester resin & 5 x Helical bars These helical bar crack stitching kits comprise of the following: > 5 x 1mtr x 6mm diameter helical bars in 304 grade austenetic stainless steel > 3 x 400mm Surebond Polyester Anchoring Resin 400ml with relevant number of extension mixer nozzles > 1 x High quality Anchor Bond Resin Applicator Gun 1mtr length helical bars should be inserted at 450mm vertical spacing and span 500mm either side of the crack. Chase out a 35mm slot in the mortar bed. Clean the slot and dampen with a mist spray. Insert a bead of polyester resin and then press the bar into it. Overlay another bead of resin allow to cure and re-point.
PLATON P8 BASEMENT CELLAR CAVITY DRAIN WATERPROOF TANKING MEMBRANE KIT 2M x 10M ( 20m2 ) - BBA CERTIFIED PRODUCT (DELIVERY TO MAINLAND UK ONLY)
Platinum Building Chemicals
£130.00
Kit Contents: 1 Roll 2.0M x 10M Platon P8 (8mm Stud) Cavity Drain Membrane, 50 - M10 x 70mm Platinum Brick Plugs, 50 - M10 Platinum Brick Plug Sealing Washers 1 x Roll 30mm x 15M Platinum Waterseal Tape, 1 x 10mm x 160mm SDS Drill Bits. Introduction: Platon P8 membrane is manufactured from high-density polyethylene (HDPE). It is impermeable and resistant to the usual chemicals in the building construction. Studs are formed in a regular pattern on the one face of the product. The studs are spaced at approx. 25mm centres in both directions. Platon P8 is CE marked in accordance with EN 13967 and EN 13984. A separate declaration gives values for several characteristics. Platon P8 is resistant to all chemicals, to which it can be exposed, in normal building construction. A small number of aggressive chemicals (e.g. solvents), in large concentrations, can to some extent attack the product during prolonged exposure. For special applications, the supplier should be contacted, with a view to assessing necessary action. Platon P8 is supported by BBA Certification Number 01/3823. PLEASE NOTE: This type of membrane cannot be plastered or plasterboarded onto, however battens can be fixed onto the brick plugs and plasterboard can be fixed to the battens, for more information please call our technical department.
CELLAR/BASEMENT TANKING MEMBRANE KIT 2M x 20M - 40m2 P8
DB Products
£173.00
40m2 (2m x 20m) BASEMENT TANKING MEMBRANE DAMP PROOFING KIT 8mm STUD PROFILE Basement Tanking Membrane is designed for use on basement walls and basement floors,Cellar Conversions etc This basement waterproofing membrane leaves an impermeable waterproof surface, enabling dry-wall lining on studs & direct laying of floors. When rolled out, it is transparent so that the substrate can be seen which allows the installation of Brick Plugs and Seals much easier. This membrane is a high quality strong durable HDPE cavity drain membrane with a stud profile of 8mm. Joints and laps should be adequately sealed by using the sealer provided Kit consists of the following 1 x Roll Cavity Drain Membrane (STUD PROFILE OF 8mm) size: 2 mtr x 20 mt (40m²) 1 Roll Double Sided Waterproof Sealing Tape 30mm x 30mtrs Brick Plugs complete with water proof Seals - Qty 100
Land Drain Filter Sleeve 80mm x 25mtrs
Alliance Remedial Supplies
£33.95
Perforated land drain filter sleeve Perforated land drain filter sleeve prevents the unwanted sand and silt particles from entering and clogging perforated drainage pipes. It is recommended for the protection of all underground drainage systems in all soil types. It is particularly suited for use in sandy and silty soil conditions. The durable knit construction is seamless and can be used as a filter envelope to cover various types of perforated drainage materials including straight wall and corrugated HDPE, steel, aluminium and PVC pipes. It is a low cost and time saving alternative to backfilling with expensive, heavy, and sometimes hard to find granular backfill materials. The specially knit fabric allows very fine soil particles to pass through and into the perforated pipe that are subsequently discharged from the drainage pipe with the water. The remaining larger soil particles that are blocked from passing through the fabric, bridge against each other on the outer surface of the fabric. Like granular backfill materials, the bridging effect of these soil particles improves the permeability of the native backfill materials immediately surrounding the perforated drainage pipe.
DAMP PROOFING ECO MESH MEMBRANE 2.5mm STUD 1x20m (20M2)
Alliance Remedial Supplies
£120.00
Damp Proofing Cavity Mesh Membrane 20m2 Damp proofing cavity mesh membrane 20m2 with 2.5mm stud profile. Multi functional membrane with strong mesh welded to the face of a high quality high density polyethylene membrane used in re-plastering over a new chemical damp proof course, isolating soil retaining walls, basement and cellar waterproofing and insulating cold walls. Used by damp proofing contractors, Plastering contractors, Builders and DIY. Ideal for a dot and dab plasterboard finish but can also be rendered. Roll dimensions: 1mtr (W) x 20mtrs (L) 2.5mm profile stud PP cavity mesh membrane ideal for re-plastering after the installation of a chemical DPC or areas of damp such as chimney breasts. Suitable for dot and dab process with plasterboard. Blue/translucent colour and very flexible. Easy to fix. Requires Plaster Plug fixings to fix to the wall at 15 plugs per m2.Membrane can be supplied in blue or clear/grey.
DryFix DPC Damp Proofing Injection Cream 380ml (BBA Approved) x3
Alliance Remedial Supplies Limited
£31.00
DryFix DPC Damp Proofing Injection Cream 380ml (BBA) x 3 DryFix DPC damp proofing injection cream is the trade mark registered brand of Alliance Remedial Supplies for damp proofing treatments and paints. Our branded DPC injection cream for the treatment of rising damp is accredited by the BBA. Certificate issue number: 16/5313. It offers 25% active ingredient which is higher than most brands in the market place. DryFix DPC damp proofing injection cream is a Silane based chemical cream that is easy to apply without the need for specialist equipment. The Silane cream works by migrating through the mortar bed once injected through a series of pre-drilled holes. Moisture within the mortar triggers the resin carried within the cream to create a pore liner within the mortar. Once fully cured, a new, fully formed damp proof course becomes effective. DryFix DPC damp proofing injection cream is suitable for specialist damp proofers and general trades. A 20 year performance guarantee is available on request. This product is suitable for cavity and solid brick walls. Stone and rubble filled walls. For best results, this product should be applied in accordance with the British Standard 'Code of Practice for Installation of Chemical Damp Proof Courses' BS 6576 (2005). Contaminated plaster should be removed and the walls re-plastered to an appropriate re-plastering specification. Call Alliance Remedial Supplies for advice on this.
DAMP PROOF MESH MEMBRANE KIT 2.5mm STUD 5M2 & BAG OF 100 PLASTER PLUG FIXINGS
Alliance Remedial Supplies
£65.00
5m2 Damp Proofing Cavity Mesh Membrane Kit 2.5mm stud depth Roll size 1mtr wide x 5mtrs long (5M2 area) Bag of 100 x Plaster Plug Fixings 8mm x 70mm For use in dot and dab replastering over a new DPC Injection course, insulating cold and damp walls. Basement Waterproofing Ideal for Damp Proofers - Plasterers - General Builders - DIY 2mm stud profile and roll size 1mtr wide x 5mtrs long, lightweight HDPE waterproof membrane provides resistance to damp, salts and vapour. Apply plug fixings at 250mm centres and secure a firm fix to the wall. Apply dab grout and fix plasterboard. For very wet walls Plaster plugs should be sealed with Butyl Rope. Colour of the membrane can be either clear/grey or blue.
Helical Crack Stitch Bars x 10 1mtr Long x 6mm For Brick and Stone Wall Repairs
Alliance Remedial Supplies
£33.00
For carrying out reinstatement crack stitch repairs to existing masonry or block work. FEATURES: Grade 304 austenetic stainless steel Dimension 1000mm x 6mm Sheer load 8.1kN - Tensile load 9.75kN Invisible repair Excellent bonding capability Structure stabilised to original strength
Bond It Mega Stik 750ml Plasterboard Adhesive X 6 With Gun & Cleaner
Bond It
£55.17
Bond It Mega Stick 750ml Plasterboard Adhesive Kit This kit comprises: 6 x Bond It Mega Stick PU Adhesive 750ml 1 x Bond It Heavy Duty Teflon Coated Professional PU Foam Gun 1 x Bond It Solvent Foam Gun Cleaner 500ml 1 x 750ml Mega Stick can fix up to 5 standard size plasterboards. Features: Fast curing adhesive for use in fixing plasterboard and insulation boards to brick and concrete walls, to metal and timber stud battens and for fixing roof decking and floor boards to beams. It can also be applied directly to bitumen coated surfaces. By applying with foam applicator there is no mess, no waste and no fuss. No heavy bags of adhesive, dust and less space taken up to work in. Cured in 1 hour ready for skimming Advisory Because GUN FOAM CLEANER for applicator guns contains acetone, it may dissolve or discolour surfaces such as plastics, lacquers, coatings, paints, textiles etc. Use with extreme care and test suitability before use. Important: Only fresh adhesive can be removed with GUN FOAM CLEANER. For guidance advice on the safe use, storage and handling of the Pu Polyurethane expanding gun grade foam please refer to the safety data sheet For guidance advice on the safe use, storage and handling of the Gun Foam Cleaner please refer to the safety data sheet
DryFix DPC Damp Proofing Injection Cream 380ml (BBA Approved) x4
Alliance Remedial Supplies Limited
£38.75
DryFix DPC Damp Proofing Injection Cream 380ml (BBA) x 4 DryFix DPC damp proofing injection cream is the trade mark registered brand of Alliance Remedial Supplies for damp proofing treatments and paints. Our branded DPC injection cream for the treatment of rising damp is accredited by the BBA. Certificate issue number: 16/5313. It offers 25% active ingredient which is higher than most brands in the market place. DryFix DPC damp proofing injection cream is a Silane based chemical cream that is easy to apply without the need for specialist equipment. The Silane cream works by migrating through the mortar bed once injected through a series of pre-drilled holes. Moisture within the mortar triggers the resin carried within the cream to create a pore liner within the mortar. Once fully cured, a new, fully formed damp proof course becomes effective. DryFix DPC damp proofing injection cream is suitable for specialist damp proofers and general trades. A 20 year performance guarantee is available on request. This product is suitable for cavity and solid brick walls. Stone and rubble filled walls. For best results, this product should be applied in accordance with the British Standard 'Code of Practice for Installation of Chemical Damp Proof Courses' BS 6576 (2005). Contaminated plaster should be removed and the walls re-plastered to an appropriate re-plastering specification. Call Alliance Remedial Supplies for advice on this.
Land Drain Filter Sleeve 100mm x 25mtrs
Alliance Remedial Supplies
£34.95
Perforated land drain filter sleeve prevents the unwanted sand and silt particles from entering and clogging perforated drainage pipes. It is recommended for the protection of all underground drainage systems in all soil types. It is particularly suited for use in sandy and silty soil conditions. The durable knit construction is seamless and can be used as a filter envelope to cover various types of perforated drainage materials including straight wall and corrugated HDPE, steel, aluminium and PVC pipes. It is a low cost and time saving alternative to backfilling with expensive, heavy, and sometimes hard to find granular backfill materials. The specially knit fabric allows very fine soil particles to pass through and into the perforated pipe that are subsequently discharged from the drainage pipe with the water. The remaining larger soil particles that are blocked from passing through the fabric, bridge against each other on the outer surface of the fabric. Like granular backfill materials, the bridging effect of these soil particles improves the permeability of the native backfill materials immediately surrounding the perforated drainage pipe.
DAMP PROOFING ECO MESH MEMBRANE 2.5mm STUD 1x10m (10M2)
Alliance Remedial Supplies
£75.00
Damp Proofing Cavity Mesh Membrane 10m2 Damp proofing cavity mesh membrane 10m2 with 2.5mm stud profile. Multi functional membrane with strong mesh welded to the face of a high quality high density polyethylene membrane used in re-plastering over a new chemical damp proof course, isolating soil retaining walls, basement and cellar waterproofing and insulating cold walls. Used by damp proofing contractors, Plastering contractors, Builders and DIY. Ideal for a dot and dab plasterboard finish but can also be rendered. Roll dimensions: 1mtr (W) x 10mtrs (L) 2.5mm profile stud PP cavity mesh membrane ideal for re-plastering after the installation of a chemical DPC or areas of damp such as chimney breasts. Suitable for dot and dab process with plasterboard. Blue/translucent colour and very flexible. Easy to fix. Requires Plaster Plug fixings to fix to the wall at 15 plugs per m2.Membrane can be supplied in blue or clear/grey.
DryFix DPC Damp Proofing Injection Cream 380ml BBA x 4 Kit
Alliance Remedial Supplies Limited
£46.12
DryFix DPC Damp Proofing Injection Cream 380ml (BBA) x 4 Kit DryFix DPC damp proofing injection cream is the trade mark registerred brand of Alliance Remedial Supplies for damp proofing treatments and paints. Our branded DPC injection cream for the treatment of rising damp is accredited by the BBA. Certificate issue number: 16/5313. It offers 25% active ingredient which is higher than most brands in the market place. DryFix DPC damp proofing injection cream is a Silane based chemical cream that is easy to apply without the need for specialist equipment. The Silane cream works by migrating through the mortar bed once injected through a series of pre-drilled holes. Moisture within the mortar triggers the resin carried within the cream to create a pore liner within the mortar. Once fully cured, a new, fully formed damp proof course becomes effective. DryFix DPC damp proofing injection cream is suitable for specialist damp proofers and general trades. A 20 year performance guarantee is available on request. This product is suitable for cavity and solid brick walls. Stone and rubble filled walls. For best results, this product should be applied in accordance with the British Standard 'Code of Practice for Installation of Chemical Damp Proof Courses' BS 6576 (2005). Contaminated plaster should be removed and the walls re-plastered to an appropriate re-plastering specification. Call Alliance Remedial Supplies for advice on this. This kit comprises of the following: 4 x DryFix DPC Injection Cream 380ml 1 x 400mm Mastic Applicator Gun 1 x 12mm Alpen Carbide Tipped SDS Plus Drill Bit 1 x Extension nozzle This volume of cream will treat 15 linear meters of 4.5″ single brick wall or 7.5 linear meters of 9″ solid brick wall. Please allow for wastage and porous brick by at least 10% volume.
DryFix DPC Damp Proofing Injection Cream 380ml (BBA Approved) x 1
Alliance Remedial Supplies Limited
£15.44
DryFix DPC Damp Proofing Injection Cream 380ml (BBA) x 1 DryFix DPC damp proofing injection cream is the trade mark registered brand of Alliance Remedial Supplies for damp proofing treatments and paints. Our branded DPC injection cream for the treatment of rising damp is accredited by the BBA. Certificate issue number: 16/5313. It offers 25% active ingredient which is higher than most brands in the market place. DryFix DPC damp proofing injection cream is a Silane based chemical cream that is easy to apply without the need for specialist equipment. The Silane cream works by migrating through the mortar bed once injected through a series of pre-drilled holes. Moisture within the mortar triggers the resin carried within the cream to create a pore liner within the mortar. Once fully cured, a new, fully formed damp proof course becomes effective. DryFix DPC damp proofing injection cream is suitable for specialist damp proofers and general trades. A 20 year performance guarantee is available on request. This product is suitable for cavity and solid brick walls. Stone and rubble filled walls. For best results, this product should be applied in accordance with the British Standard 'Code of Practice for Installation of Chemical Damp Proof Courses' BS 6576 (2005). Contaminated plaster should be removed and the walls re-plastered to an appropriate re-plastering specification. Call Alliance Remedial Supplies for advice on this.
Land Drain Filter Sleeve 60mm x 25mtrs
Alliance Remedial Supplies
£27.50
Perforated land drain filter sock sleeve Perforated land drain filter sleeve prevents the unwanted sand and silt particles from entering and clogging perforated drainage pipes. It is recommended for the protection of all underground drainage systems in all soil types. It is particularly suited for use in sandy and silty soil conditions. The durable knit construction is seamless and can be used as a filter envelope to cover various types of perforated drainage materials including straight wall and corrugated HDPE, steel, aluminium and PVC pipes. It is a low cost and time saving alternative to backfilling with expensive, heavy, and sometimes hard to find granular backfill materials. The specially knit fabric allows very fine soil particles to pass through and into the perforated pipe that are subsequently discharged from the drainage pipe with the water. The remaining larger soil particles that are blocked from passing through the fabric, bridge against each other on the outer surface of the fabric. Like granular backfill materials, the bridging effect of these soil particles improves the permeability of the native backfill materials immediately surrounding the perforated drainage pipe.
Bond It Mega Stik 750ml Plasterboard Adhesive X 4 With Gun & Cleaner
Bond It
£44.18
Bond It Mega Stick 750ml Plasterboard Adhesive Kit This kit comprises: 4 x Bond It Mega Stick PU Adhesive 750ml 1 x Bond It Heavy Duty Teflon Coated Professional PU Foam Gun 1 x Bond It Solvent Foam Gun Cleaner 500ml 1 x 750ml Mega Stick can fix up to 5 standard size plasterboards. Features: Fast curing adhesive for use in fixing plasterboard and insulation boards to brick and concrete walls, to metal and timber stud battens and for fixing roof decking and floor boards to beams. It can also be applied directly to bitumen coated surfaces. By applying with foam applicator there is no mess, no waste and no fuss. No heavy bags of adhesive, dust and less space taken up to work in. Cured in 1 hour ready for skimming Advisory Because GUN FOAM CLEANER for applicator guns contains acetone, it may dissolve or discolour surfaces such as plastics, lacquers, coatings, paints, textiles etc. Use with extreme care and test suitability before use. Important: Only fresh adhesive can be removed with GUN FOAM CLEANER. For guidance advice on the safe use, storage and handling of the Pu Polyurethane expanding gun grade foam please refer to the safety data sheet For guidance advice on the safe use, storage and handling of the Gun Foam Cleaner please refer to the safety data sheetShipped by Alliance Remedial Supplies Ltd. Bond It distributors
DryFix 3000 Self Adhesive Bitumen Tanking Membrane (5.25m2)
Alliance Remedial Supplies
£54.99
DryFix 3000 Self Adhesive Bitumen Tanking Membrane DryFix 3000 Self Adhesive Bitumen Tanking Membrane is a cold applied, heavy duty and robust below ground waterproofing membrane. DryFix 3000 self adhesive bitumen tanking membrane is used for internal and external tanking of underground structures, reservoirs, car park and roof decks, subways, lift shafts and retaining walls. It is satisfactory for use as a waterproofing membrane for type A basement constructions grades up to and including 3 as defined in Table 1 of BS 8102:2009. Its advanced cross orientated HDPE backing film gives improved technical performance on tear strength and tensile strength, puncture resistance and dimensional stability. It also offers good conformability for site application. Installed following an application of Hydroprufe 3000 Primer it will withstand a 6 meter head of water. Roll dimension: 1.05mtrs wide x 5mtrs long. Roll dimension: 1.05mtrs wide x 10mtrs long. Roll dimension: 1.05mtrs wide x 15mtrs long. Please note: Adjacent rolls should allow a minimum side overlap of 50 mm and end overlap of 100mm This overlap is in addition to any overlap on to the selvedge. Prior to overlapping adjacent rolls the release strip protecting the selvedge should be removed. This membrane should be protected against damage from the back-fill process. This can be achieved with either a rigid insulation board such as Danopren TR XPS or a Heavy Duty Protection Board.
Helical Bar Reinforcement Repair Kit With Polyester Resin Tubes x 3 Mixer Nozzles x 3 Helical Bars x 5 by Alliance Remedial Supplies (No Applicator Gun)
Alliance Remedial Supplies
£68.95
Helical bar crack repair kit with polyester resin & 5 x Helical bars PLEASE NOTE THIS KIT DOES NOT INCLUDE AN APPLICATOR GUN These helical bar crack stitching kits comprise of the following: > 5 x 1mtr x 6mm diameter helical bars in 304 grade austenetic stainless steel > 3 x 400mm Surebond Polyester Anchoring Resin 400ml with relevant number of extension mixer nozzles 1mtr length helical bars should be inserted at 450mm vertical spacing and span 500mm either side of the crack. Chase out a 35mm slot in the mortar bed. Clean the slot and dampen with a mist spray. Insert a bead of polyester resin and then press the bar into it. Overlay another bead of resin allow to cure and re-point.
Drive Fix Remedial Wall Tie Kit (Wall Tie - 220mm Drill - 450mm)
Alliance Remedial Supplies
£197.40
Drive Fix Remedial Wall Tie Kit - 100 x Drive Fix Ties - 1 x SDS Adaptor Tool - 2 x Drill Bits Drive Fix Remedial Wall Tie Kit offers the following options: A quantity of 100 Drive Fix Remedial Helical Wall Ties in 8mm diameter by 200mm or 220mm long. The installation process requires that a 6mm diameter pilot hole is drilled first into the brick to accept the Drive Tie which is hammered into the brick using the SDS Adaptor Tool provided with the kit. Note: The diameter of the pilot hole is between 5.5mm - 6.5mm for 8mm Drive Ties but which is also determined by the nature of the host material. Our Kit includes as standard a 6mm x 160mm SDS Plus drill bit with the optional choice of either a 6mm x 310mm or a 6mm x 450mm SDS Plus drill bit if you need to achieve an embedment depth of over 50mm for a 220mm long tie. We recommend the shorter 6mm x 160mm drill bit is used to reduce 'whip' when using the longer drill bit. This kit is great value for builders, damp proofers and wall tie contractors working on smaller jobs to an area of between 20 - 40m2.