Axminster Air

Axminster Air AW50N 18G Brad Nailer
Axminster Air
£62.99
The most popular air nailer in our range, this lightweight trade-rated nailer fires 18 gauge T-headed brad nails from 15mm to 50mm in length and with its low air consumption can be used with any of the smaller 25L capacity compressors. It can be used with standard trigger firing or in bump mode where, with the trigger engaged, a nail is delivered each time the safety stop is depressed, useful for fast fixing. The gun is easy to load and has a re-load sight so that the operator can see when the magazine is empty. Other useful features are the depth adjustment which controls the depth to which the nail is driven, the adjustable air exhaust outlet and the quick release front cover to give easy access for clearing jammed nails. A 1/4" BSP male bayonet fitting is provided in the back of the tool for direct connection to the airline using quick release bayonet fittings. Details of suitable airlines and fittings can be found in the Air Hose's section. Supplied in a plastic storage case.
Axminster Air AWHP Headless Pinner
Axminster Air
£39.76
This lightweight trade-rated air tool, which drives 24 gauge headless pins from 12mm to 20mm long, is great for furniture, mouldings, decorative trim and glazing beads. It has a 1/4" BSP female fitting and is suitable for use with smaller compressors. Supplied with a 1/4" BSP Quick Release bayonet fitting. Details of suitable airlines and fittings can be found in the Airline Fittings section. Firing pins for this pinner are available in two sizes. 18mm piston head size for pre 2015 models (100140) and 22mm piston head size for post 2015 models (101805).
Axminster Air FN2890D Framing Nailer
Axminster Air
£217.96
This is a heavy duty on-site-use nailer, just the job for trusses, decking, framing and sheeting. Exceptionally light and strong due to its magnesium alloy casing. The FN2890D Framing Nailer fires collated 28° clipped head nails from 50mm to 90mm with a diameter from 2.9mm minimum, to 3.3mm maximum. The nailer has a fast loading magazine with load sight and maximum capacity of 84 nails (2 strips). It's handle has a rubberised grip for user comfort, especially useful for shock absorbing and a variable position air exhaust vent. Supplied with 2 triggers to allow single action firing only (to prevent a double firing) or the faster bump feed firing action. Also comes supplied in a sturdy case with safety goggles, service tools and lubrication oil. Please note that this nail gun requires a compressor capable of delivering 7cfm minimum. The tool has a 1/4" BSP female inlet; refer to the Airline Fittings section for details of suitable airlines and fittings.
Axminster Air AWMN Air Masonry Nailer
Axminster Air
£116.00
A very impressive air operated masonry nailer which will drive hardened nails with ease into a whole variety of hard surfaces such as brick, light concrete, insulating blocks, screed and plaster. The range of nail length, from 18mm to 64mm and the 80 nail capacity quick loading magazine make it a natural for second fix work. There is the usual safety latching system and the air exhaust outlet directs the exhaust to the front. Light in weight, safe to use and extremely reliable, this nailer can save a huge amount of time on site as so many tasks can be done with just one tool. The tool has a 1/4" BSP female inlet; refer to Airline Fittings section for details of suitable airlines and fittings. For quick release bayonet fitting use 100313 or 410251 (swivelling).
Axminster Air DA1564 15 Gauge Finish Nailer
Axminster Air
£129.50
An industrial finishing nailer for both interior and exterior use. The non-marking tip device and the adjustable depth control make it just as good for fine furniture and upholstery work as it is for battening and framing. Easy loading of nails into the rear entry angled magazine coupled with the powerful nailing action make this a real time saver on site. The swivelling exhaust deflector and rubber grip handle makes for comfortable use. The nails are 34°, 15 gauge (1.8mm) with 3mm heads. The nailer will take nails with a minimum length of 15mm and a max of 50mm. The tool has a 1/4" male bayonet fitting. Lubricate regularly. Please refer to Airline Fittings section for details of suitable airlines and fittings. For quick release bayonet fitting use 100313 or 410251 (swivelling). Supplied in a plastic storage case.
Axminster Air 9040L Air Stapler
Axminster Air
£65.95
This heavy duty model uses narrow crown 18 gauge staples 5.8mm wide in lengths from 16mm to 38mm long. Very good for applications such as stapling hardboard panels, thin ply, T & G boards, fencing panels etc. Supplied with safety latch and swivelling exhaust air vent. The tool comes supplied with a 1/4" BSP bayonet; refer to the Airline Fittings section for details of suitable airlines and fittings.
Axminster Air 6-22 Air Stapler
Axminster Air
£46.00
A solidly made trade rated stapler, weighing in at 1.25kg and suitable for long periods of continuous use. It uses 20 gauge (0.9mm) wide crown (11.2mm) staples and in lengths from 6mm to 22mm. Primarily used for upholstery, it can be used for many other similar trades. Supplied with a swivelling exhaust air vent. The tool comes supplied with a 1/4" BSP bayonet; refer to the Airline Fittings section for details of suitable airlines and fittings. For quick release bayonet fitting use 100313 or 410251 (swivelling).
Axminster Air T50P 16G Brad Nailer
Axminster Air
£106.50
This medium weight trade-rated nail gun fires 16 gauge T-headed brad nails from 20mm to 50mm in length. With its low air consumption, this nailer can be used with any of the smaller 25 litre capacity compressors. It can be used with standard trigger firing or in bump mode where, with the trigger engaged, a nail is delivered each time the safety stop is depressed, useful for fast fixing. The gun is easy to load and the handle has a high grip rubber covering. An adjustable exhaust air outlet means that the exhaust can be directed to where convenient. A 1/4" BSP quick release male bayonet fitting is provided in the back of the tool for direct connection to the airline. Details of suitable airlines and fittings can be found in the Air Hose section. Supplied in a plastic storage case.
Axminster Air Line Hose with Quick Release Fittings - 15m
Axminster Air
£45.70
Axminster Air Line Hose with Quick Release Fittings - 15m
Axminster Air OKERT Crimp-On Air Hose Clamps (Pkt 10)
Axminster Air
£7.50
These hose clamps are effective, reliable and easy to fit and set. Fixing them in place only requires a squeeze with a pair of pincers. Internally they are completely smooth. The "tongue-in-groove" feature exerts continuous radial pressure on the assembled parts over a full 360°. Packs of 10, sized for 3/8" air hose.
Axminster Air Line Hose with Quick Release Fittings - 5m
Axminster Air
£29.99
Axminster Air Line Hose with Quick Release Fittings - 5m
Axminster Air Line Hose with Quick Release Fittings - 10m
Axminster Air
£37.80
Axminster Air Line Hose with Quick Release Fittings - 10m
Axminster Air AW32NS Nailer Stapler
Axminster Air
£63.95
This lightweight trade-rated machine will fire a choice of either 18 gauge T-headed nails 10-30mm or narrow crown staples in the range of 15mm to 32mm and with its low air consumption will work off one of the smaller 25 litre tank compressors. It can be used with standard trigger firing or in bump mode where, with the trigger depressed, a fixing is delivered each time the safety stop is depressed, useful for fast fixing. The gun is easy to load and has a re-load sight so that the operator can see when the magazine is empty. Other useful features are the depth adjustment which controls the depth to which the nail is driven, the adjustable air exhaust outlet and the quick release front cover to give easy access for clearing jammed nails. Supplied with a 1/4" BSP quick release bayonet fitting and a storage case. Details of suitable airlines and fittings can be found in the Airlines Fittings section.
Axminster R15 Air Riveter Kit
Axminster
£87.95
A production rivet gun kit with four different rivet heads for blind rivets 3mm, 4mm and 5mm. The rivet is easily set with a pull on the trigger and without the risk of damaged knuckles. On the rear of the gun is a receiver which catches rivet shanks and stores them ready for later disposal. Supplied in a kit box with an impressive collection of rivets, jaws, noses, spare parts and tools. This gun will work on virtually any compressor with a reservoir tank. 1/4" BSP female fitting.
Axminster APF 10 Evolution Powered Respirator
Axminster Tools & Machinery
£229.96
This positive pressure powered respirator eliminates the drawbacks encountered with standard negative pressure face masks. The motor unit blows filtered air down over your face at a rate of 160L/min. Fatigue caused by having to suck through a filter is no longer a problem; breathing is normal and comfortable. The air exiting around the sides and bottom of the mask is at slightly higher pressure than that outside, so forms a most effective seal. Beards are not a problem. If you wear glasses, these will not fog or mist up as you breathe out. With the motor and filters mounted on the peak of the bump cap and the battery at the rear, the balance of the APF 10 Evolution unit is excellent. Combined with the low overall weight (680g), it is very comfortable. The Li-Ion batteries give you a run time of 8 hours on a full charge. The filters are easy to inspect and replace. The bump cap's outer cover is removable for washing. The unit provides respiratory protection to EN12941:1998 + A2:2008 TH1P. The bump cap gives head protection to EN812. The clear visor gives you a wide field of vision along with impact protection to EN.166.B.1. Supplied with an 8-hour battery, plus charger, two filters, a flow-rate meter and complete instructions all within a strong storage box. Respiratory protective equipment (RPE) should not be used as the only means of control as it should complement other control measures such as a dust extraction system. Each RPE type and class is categorised by an assigned protection factor (APF). The APF is a number rating that indicates how much protection that RPE is capable of providing. For example, RPE with an APF of 10 will reduce the wearer's exposure by at least a factor of 10 if used properly, or, to put it another way, the wearer will only breathe in one-tenth or less of the amount of substance present in the air. Evolution is a registered trade mark of JSP Ltd, used under licence by Axminster Tool Centre Ltd.
Axminster Engineer Series CT-502H Extractor
Axminster Engineer Series
£849.96
The CT-502H is a purpose-built extractor for metal dusts. It has a unique air flow system that separates out the dust from the airflow to allow the various weights of metal particles to fall into either the large primary collection bin or a smaller secondary bin. A powerful 1.125kW 230V 1ph motor creates up to 1,360 m³/hr airflow through a choice of either a 150mm inlet or a pair of 100mm inlets. The impeller fan is an aluminium casting with efficient curved blades. The aluminium impeller construction prevents impact sparking from metal particles.The machine is heavily built and is mounted on castors for easy mobility. A large grab handle is fitted to make this an easy task. The three stage filters are mounted inside a drop down door, also giving access to the secondary collection bin. The main collection bin is mounted on rollers and is easily accessed through a large door. This machine would be a perfect partner for a metal grinding or linishing machine, keeping your workshop and the operator clean. Heat resistant ducting hose is recommended, please see accessories. N.B. requires a 16A supply
Axminster Craft AC37E 1HP Extractor
Axminster Craft
£159.95
This extractor can be used in small home workshops for common wood machining tasks where a higher airflow than provided by a vacuum extractor is required. The quiet running induction motor provides plenty of power to extract from many small workshop machines. The inlet diameter is 100mm(4"), the outlet into the bag is 100mm(4") and the airflow is sufficient to handle the majority of waste likely to be produced in the small home workshop. A useful feature is that it can be used either on the floor or suspended from a sturdy wall using the two hanging brackets provided. A useful grab handle and castors allow easy mobility. Hose not supplied; see extraction hose selection for further details. Please note that this is a chippings extractor and should not be expected to collect fine dust. As with all the high volume low pressure airflow machines, the inlet should not be restricted to below 75mm diameter and the bag should be emptied regularly. Spare bag provided.
Axminster Craft AC300DS Disc Sander
Axminster Craft
£179.94
A good value-for-money disc sander which will be a great asset in any hobbyist's workshop. The 300mm disc is driven by a quiet 750W induction motor and takes the full range of our 300mm diameter self-adhesive discs. Tip!Self adhesive discs can easily be removed complete with their glue by gently warming with a hot air gun before removing. The motor is controlled by a no-volt-release switch and there is a brake provided to slow the disc down in a reasonable time. The cast iron sanding table has a ground top surface and is provided with a slot for the adjustable mitre fence, used for end grain sanding. The table tilts to 45° and is firmly locked in position with heavy duty handles at both ends. Dust is extracted from the bottom of the disc via a shroud which terminates in a 63mm diameter outlet. A 450mm length of flexible hose is provided with the machine; this has a 60mm diameter sleeve at the end which will connect directly to an extractor.
Axminster Trade AT535SS Scroll Saw
Axminster Trade
£699.96
This 535mm(21") scroll saw is the mid sized model from a range of three with some really different features not found on any other machine. It is constructed mainly from plate steel including a 7mm heavy gauge steel table with an epoxy painted surface. Two unique features make this machine stand out from any other. Firstly, the blade actuating arms are very short, driven by a lever and rod mechanism. This gives very high control of the blade plus exceptionally low vibration. Secondly, the whole arm assembly tilts 45° from the vertical right and 35° left, leaving the table horizontal. This allows much better control of the work, due to greater visibility and being able to work at a natural position. You are not fighting gravity or bending your wrists into awkward positions. This machine is not short of other features, having a variable speed control system giving from 400-1,500 strokes per minute. Upgraded with the PEGAS "Blade Chuck" blade clamps which are much lighter, reducing vibration which reduces stress on the machine. Blade changing is easy and tool free, with two hand clamps and a quick release lever. An air blower and work hold down are provided. Plus there is efficient dust collection when connected to a suitable fine dust extractor. You are recommended to permanently mount the machine onto your workbench or to one of the dedicated stands available as an option. Using unpinned blades means there is a large selection of blades available or you can use 150mm lengths of 1/4" bandsaw blade, ideal for cutting thicker materials. Supplied with an assortment pack of Swiss made PEGAS blades. This is a serious machine for craft or joinery work, not the same as any other. This machine was previously known as the EX-21.
Flexible Shaft & Microplane Rotary Shapers - Package Deal
Axminster
£81.19
Package deal comprises the one each of the 25mm(1") and 50mm(2") Microplane Rotary Shaper and the Axminster General Duty Flexible Shaft. Microplane Rotary Shaper Enjoy shaping with precision and control on wood, plastic, plasterboard, rubber and more instead of coarse sandpaper. Hundreds of razor sharp mini teeth in the form of a drum, for use with a power drill. Microplane blades are made from 400 series stainless steel and have been fitted to an aluminium extrusion which is provided with a 8mm shank. The beauty of this method of shaping is the resulting waste, which is tiny shavings rather than dust, and the superior finish left by a tool that cuts rather than scrapes, tears or abrades, creating clouds of dust. Recommended to run at between 1,000-2,000rpm and not exceed 2,500rpm. The Rotary Shapers rotate clockwise. Materials being fed into the shaper should be fed left of centre to reduce kickback. Supplied in two sizes 25mm(1") and 50mm(2"), with replacement blades available separately for both. Axminster General Duty Flexible Shaft One of the most useful attachments one can have for a drill and one which needs to be used with the Universal drill clamp so that the drill can be safely left running. The flexible shaft is an extension of the drill chuck and is great for polishing, de-rusting, sanding, carving and many other uses. The Axminster flexible shaft has a 10mm capacity keyed chuck attached to one end and is 1.3m long with a high quality drive and very durable outer casing. The spigot that should be attached to the chuck of the drill is 6mm in diameter.