Sioux Chief

Water Hammer Hydra Arrester 25mm 1
SIOUX CHIEF
£258.11
Room or shocking hoses & # x202 °F;?Easy to install and with a lifetime guarantee, Water Hammer surge-arrester is the ultimate protection against water hammer damage.You are in a room or shocking Water Pipes, every time the washing machine, toilet in the toilet or dishwasher valves close & # x202 °F;?Only Regret The Late Night & # x202 °F;? & # x202 °F; Dimensions: 15.1 inch (L) x 2.1/8 "(W) This unit is for large installions which Water Hammer caused by multiple devices. Can support a total capacity of 155-330 unit where a unit is typically Device keeps liquid hot/coldShower 2 1Bath 1.5WC 2Basin/Sink 1.5Dishwasher 3Washing Machine 3Garden Tap 2Please contact us at customerservice @ fixthebog. com for help the size water surge arrestersPlease note that you need a hole on the hot and cold circuits if the water hammer is affecting the
Sioux Chief 652-A Water Arrestor
APR Supply Co.
£14.82
1/2" WATER HAMMER ARRESTOR
Stop Noisy Pipes Prevent Water Hammer Banging pipes Arrester Water shock Preventer Thumping Pipes for Washing Machines Dishwashers
Sioux Chief
£34.06
Room or shocking hoses?Easy to install, simple, Water Hammer surge arresters are the ultimate protection against water hammering sounds.You are a room where the water pipes shock you, every time the washing machine or dishwasher valves close?Only Regret The Late Night?This device is the solution for the washing machine and dishwasher.For your washing machine or dishwasher shut-off valve.DIY fit.No need for other parts.Easy to set up. Just plug it in. Simply.Out of the shut-off valve for washing machines and dishwashers.Unscrew the connection of the shut-off valve hose.Compatible with the shut-off valve capable of 202°F; can be fitted at any angle.Screw the hose to.Up the Back To Restore water shut-off valve and check for leaks.
Stop Pipes From Banging Noise Preventer Reflex 0.16Ltr Potable Expansion Vessel Shock Arrestor PV016C
Altecnic Reflex
£22.41
Altecnic - Reflex 0.16Ltr Potable Expansion Vessel Shock Arrestor PV016C If system pressure is high, the water flowing through it has greater momentum which when brought to a sudden stop, usually caused by the closure of lever operated taps or valves such as those in dish washers and washing machines, creates a shock effect causing pipes to shudder and vibrate. This Altecnic stainless steel expansion vessel can be used as a water hammer arresters on single outlets, such as taps or washing machines, or on small groups of outlets, such as a bathroom. This will remove both the anoying knocking that can be caused, but also provide a solution for eventual damage that might be caused by moving pipes spliting or cracking due to vibration over time. The expansion vessel shock arrester should be installed close to taps or valves in order to minimise the effect of shock on the system. Technical Data: Max. working pressure: 15 bar Max system Temperature: 100°C Pre-charge pressure: 3.5 bar PED: 97/23/EC Material: Stainless Steel Connection: 1/2" Male BSP WRAS approved product Dimensions: Height: 112mm Diameter: 80mm
Stop Noisy Pipes for Baths Taps Basins Toilets Prevent Water Hammer Banging pipes Arrester Water shock Preventer Thumping Pipes kit includes 15mm x 15mm x 1/2inch tee and PTFE tape by Sioux Chief

Notice: Undefined property: stdClass::$Manufacturer in /var/www/vhosts/wundr-shop.it/httpdocs/QualitTradeTools/brand/content.php on line 145

£34.94
Thomas Dudley MiniRester Water Hammer Arrester for Washing Machine & Dishwasher 3/4 BSP

Notice: Undefined property: stdClass::$Manufacturer in /var/www/vhosts/wundr-shop.it/httpdocs/QualitTradeTools/brand/content.php on line 145

£27.95
This professional water hammer arrester helps prevent noisy and banging pipes, as well as reduce any pipework stress.
Stop Noisy Pipes for Baths Taps Basins Toilets Prevent Water Hammer Banging pipes Arrester Water Shock Preventer Thumping Pipes 2 x 15mm Compression Tee Easy Fit
Altecnic Reflex
£29.96
Altecnic - Reflex 0.16Ltr Potable Expansion Vessel Shock Arrestor with 15mm Tee PV016C Includes: 15mm Tee for ease of fitting. Washer 0.16Ltr Shock Arrestor If system pressure is high, the water flowing through it has greater momentum which when brought to a sudden stop, usually caused by the closure of lever operated taps or valves such as those in dish washers and washing machines, creates a shock effect causing pipes to shudder and vibrate. This Altecnic stainless steel expansion vessel can be used as a water hammer arresters on single outlets, such as taps or washing machines, or on small groups of outlets, such as a bathroom. This will remove both the anoying knocking that can be caused, but also provide a solution for eventual damage that might be caused by moving pipes spliting or cracking due to vibration over time. The expansion vessel shock arrester should be installed close to taps or valves in order to minimise the effect of shock on the system. Technical Data: Max. working pressure: 15 bar Max system Temperature: 100°C Pre-charge pressure: 3.5 bar PED: 97/23/EC Material: Stainless Steel Connection: 2 x 15mm Compression WRAS approved product Dimensions: Height: 135mm Diameter: 80mm
Zilmet Water Hammer Arrester WRAS Approved Stop Noisy Pipes for Baths Taps Basins Toilets Prevent Water Hammer Banging pipes
Zilmet
£23.80
Zilmet - Inox-Pro Stainless Steel Dull Finish Potable Water Hammer Arrestor 0.16ltr Water hammer is caused when a water supply outlet is closed very suddenly. This causes a change in the momentum of the water when the system suddenly goes from a lower running pressure to a higher static pressure. This momentum impacts against the now closed outlet resulting in a potentially loud banging noise. This is commonly found in "quarter turn" type tap outlets and washing machines with solenoids controlling flow. Sitting a shock arrester as close to the source of the noise as possible will cause the vessel's diaphragm to flex in response to this momentum change and prevent the audible impact against the terminal fittings. The pre charge should ideally be set to just slightly above the dynamic pressure of the system it is fitted to. Product Features: Hardwearing Reduces water hammer Suitable for hot and cold water installations
Water Hammer Arrester WRAS Approved Stop Noisy Pipes for Baths Taps Basins Toilets Prevent Water Hammer Banging pipes
FAR
£27.40
What is a WRAS Approval? Any water fitting, which when installed, will carry or receive water from the public mains water supply in the UK, must comply with the Water Supply (Water Fittings) Regulations or Scottish Byelaws. These require that a water fitting should not cause waste, misuse, undue consumption or contamination of the water supply and must be 'of an appropriate quality and standard'. WRAS Approval is the easiest way to demonstrate compliance as it is granted directly by representatives of the water suppliers and is therefore accepted by every water supplier in the UK. WRAS Product Approval: Whole products such as valves, boilers & showers undergo mechanical and water quality testing. This type of approval demonstrates full compliance with requirements of the regulations and byelaws, provided the fitting is installed according to any conditions given with the approval. WRAS Material Approval: Non-metallic materials & components, such as rubber sheet material & 'O' rings, undergo testing only for their effects on water quality. This type of approval demonstrates that the non-metallic material/component does not itself contaminate the water and therefore satisfies this particular requirement of regulations and byelaws.
Sioux Chief Mfg .75in. X 10ft. 22 Gauge Metal Hanger Strap 524-1022PK2
Sioux Chief Mfg
£5.40
Hanger strap Alternating .25" and 3/16" holes Galvanized Steel 22 gauge .75" x 10' Length: 7Width: 1Height: 4
SIOUX 660-TK
Sioux Chief Mfg
£17.73
Water hammer arrester;No more head damaged cartridges from soldering heat;Install on male iron pipe connections for tub or shower valves;Female swivel ballcock nut connection;Male ballcock threaded connection
Caleffi 525040 1/2
Caleffi
£17.20
Caleffi 1/2" Mechanical Shock Arrestor Caleffi Part Number: 525040 Maintenance Free Device To Prevent Water Hammer In Plumbing Systems Brass Body With Polymer Piston, Steel Spring & EPDM Seals Max Working Pressure: 10 Bar Operating Start Pressure: 3 Bar Max Water Hammer Pressure: 50 Bar Max Water Temperature: 90c Dimensions: Body Height (Excluding Thread): 74MM Max Diameter: 52MM Weight: 0.5KG
Thomas Dudley Ltd DW660-H Water Hammer Arrestor ¾
Thomas
£31.08
Professional water hammer arrestor that quietens noisy and banging pipes and reduces stress on pipework. L x Dia: 126 x 71mm. Connection: ¾" BSP Connection.
Sioux Chief Mfg .75in. Female Swivel Hose Thread X .75in. Male Hose Thread Mini Rest
Sioux Chief Mfg
£8.51
Water hammer arrester tee;Install on washing machine supply valves or directly to washing machine tub or shower tee;3/4-Inch female swivel hose thread connection;3/4-Inch male hose thread connection;Systems which exceed 60 PSI (414kPa) static pressure shall be installed with a pressure reducing valve upstream of the arrester.
Stop Noisy Pipes for Baths Taps Basins Toilets Prevent Water Hammer Banging pipes Arrester Water Shock Preventer Thumping Pipes 2 x 22mm Compression Tee Easy Fit
Altecnic Reflex
£29.97
Altecnic - Reflex 0.16Ltr Potable Expansion Vessel Shock Arrestor with 22mm Tee PV016C Includes: 22mm Compression Tee for ease of fitting. Washer 0.16Ltr Shock Arrestor If system pressure is high, the water flowing through it has greater momentum which when brought to a sudden stop, usually caused by the closure of lever operated taps or valves such as those in dish washers and washing machines, creates a shock effect causing pipes to shudder and vibrate. This Altecnic stainless steel expansion vessel can be used as a water hammer arresters on single outlets, such as taps or washing machines, or on small groups of outlets, such as a bathroom. This will remove both the anoying knocking that can be caused, but also provide a solution for eventual damage that might be caused by moving pipes spliting or cracking due to vibration over time. The expansion vessel shock arrester should be installed close to taps or valves in order to minimise the effect of shock on the system. Technical Data: Max. working pressure: 15 bar Max system Temperature: 100°C Pre-charge pressure: 3.5 bar PED: 97/23/EC Material: Stainless Steel Connection: 2 x 22mm Compression WRAS approved product Dimensions: Height: 135mm Diameter: 80mm