Arduino relay 1ch

TOOGOO(R) 1CH Relay Shield V2 Version 2 for WEMOS D1 mini ESP8266 WiFi Module Arduino
TOOGOO(R)
£1.35
* TOOGOO is a registered trademark. ONLY Authorized seller of TOOGOO can sell under TOOGOO listings.Our products will enhance your experience to unparalleled inspiration. TOOGOO(R) 1CH Relay Shield V2 Version 2 for WEMOS D1 mini ESP8266 WiFi Module ArduinoPackage Contents:2pcs x Normal pins 1pcs x Relay Shield Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
ILS. - DC 5V 1CH Relay Shield V2 Version 2 For D1 Mini ESP8266 WiFi Module
I LOVE SHOPPING
£4.94
Description:New Relay Shield V2 for WEMOS D1 miniMore infos is here!Package included:1 x DC 5V 1CHRelay Shield V2for WEMOS D1 mini
ILS - 433Mhz DC12V 1CH Wireless Remote Control Switch Relay Receiver Module + 2 RF Transmitter
I LOVE SHOPPING
£8.36
NOTE: The system can store for 15pcs of remotes, if the remote get more than 15pcs, the initial remote control will be lost.Feature: Wiring type: fixed terminalStandby current: 97dbmOutput terminal: NO, NC, COMRF working mode: SuperheterodyneDecoding mode: MCU software decodingTransmitting distance: >100m ( open space)Support remote type: Learning code, Fixed code(Rolling code can be design)Working mode: Momentary, Toggle, Latching Time delay (5s, 10s, 15s ) About Working mode: - Momentary: Push the remote button, the relay connects, release the remote button, the relay disconnects.- Toggle: Push once the remote button, the relay connects, push twice the remote button, the relay disconnects.- Latching: Push the remote button A, the relay connects, push the remote button B, the relay dis-connect.- Time delay mode: Push the remote control button, the relay connects, from when releasing the remote button, after 5s or 10s or 15s, the relay disconnect automatically. Clearing the code: Push the learning button on the receivers for 8 times, the codes will be cleaned.After clearing the code, all the remote control cannot work anymore. 1. Learning the code: (Momentary)Push the learning key on the receiver once time, it comes into the momentary setting mode.Wait for moment, the LED will be off , it comes into learning state.Push the remote button, LED indicator on the receiver board will flash then come off.After 3 seconds, the LED indicator will be on again, learning successfully. 2. Learning the code: ( Toggle )Push the learning key on the receiver twice, it comes into toggle setting modeWait for moment, the LED will be off, it comes into learning state.Push the remote button, LED indicator on the receiver board will flash then come off.After 3 seconds , the LED indicator will be on again , learning successfully. 3. Learning the code: ( Latching )Note: When you choose for latching mode, in
ILS. - DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver
I LOVE SHOPPING
£5.22
Specification:1.Input Voltage: DC10-14V2.Standby Current: 90dBm6.Remote Control Distance: >100 meter(In open environment)7.Decoding Way: MCU Software decoding8.Can store the number of remote control:509.Support remote control type: Fixed code, learning code10.Channel: 1CH11.Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)12.Wiring Method:Fixed wiring terminal13.Working Voltage: DC12V14.Output Current: 10A15.Rated load:10A 250VAC / 10A 125VAC10A 30VDC / 10A 28VDC16.Output:Normally open,Common,Normally closed17.Dimension:3.5cm*3cm*1.6cmWorking/output way:1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relayDescription:1. press the learning code .the indicator flash ,loosen your finger ,press any button of the remote controlthe indicator flash 2 times and off .it mean you learn it successfully .
ILS. - DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter With Receiver
I LOVE SHOPPING
£8.39
Features:Easy to install and easy to carryWith a slidable cover on the remote controlWith a hook on the remote controlUse Learning coding, stable and reliableThe wireless signal can pass through walls, floors and doorsYou can turn on or turn off the receiver with transmitter (remote control) from any place within a reliable distanceOperating Voltage: DC12VMaximum Load: 10AOperating Frequency: 433MHZ (in set)Receiver Sensitivity: -100dBmEncoding Type: learning codeBoard Size: Approx. 5.3x3.1cm/ 2.1.22"Output Working Way:1. Jog: Pressing one button is working. Loosing your finger on the same button is stop. (need one channel switch and one buttons remote control)2. Self-lock: Pressing one button for one time is working. Pressing the same button again is stop (need one channel switch and one buttons remote control)3. Inter-lock: Pressing one button is working. Pressing another button is stop (need one channel switch and 2 buttons remote control)4. Please notice that here is 1CH and 1 button wireless remote control. You can choose the self-lock or jog working/ output way, you better choose jog or self-lock, so pressing the button is open, and pressing again is close, or pressing is open, and loosing finger is closeLearning and Remove Method:1. Press the learning code. The indicator from on to off, loosen your finger, press any button of the remote control, the indicator flash 2 times and off. It mean you learn it successfully2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless remote control3. Remove/ Clean: Press the learning button about 8 seconds, the indicator turn on to off, it means the information that you keep have been removed successfullyPackage Included:1 x Learning Code Receiver1 x Remote Control
MagiDeal 3v 1CH Channel Relay Module Interface Board with Optocoupler LED 10A
MagiDeal
£3.99
Description: - One Channel 3V Relay interface board,be able to control various appliances, and equipments with large current - With output indicator, can be directly microcontroller output - It can be controlled directly by Microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) - Surrounded by fixed mounting holes, external connection use rotating crimping terminal, make connection firmer - Optical coupling isolation, input and output power optional independent control ( DC 3V )Specification: - Materials: Metal, Plastic, Electric Parts - Size: Approx. 51x31x19mm/ 2.01x1.22x0.75inch - Pole Number: 1 Channel - Load: 10APackage Includes:1 Piece Relay ModuleNote:Please allow 1-3mm differs due to manual measurementDue to the different display and different light, the picture may notreflect the actual color of the item. Thanks for your understandingGood products with excellent quality and reasonable price. Your satiscfaction is our ultimate goal of our efforts.
DIY Kits for Arduino, LDTR-WG0228 DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver Arduino Accessories
YINGGUICHENG SHOP
£13.88
Accessories for Arduino, replace old / broken parts.Assembly to new function module.LDTR-WG0228 DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch ReceiverSpecification:1.Input Voltage: DC10-14V2.Standby Current: 90dBm6.Remote Control Distance: >100 meter(In open environment)7.Decoding Way: MCU Software decoding8.Can store the number of remote control:509.Support remote control type: Fixed code, learning code10.Channel: 1CH11.Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)12.Wiring Method:Fixed wiring terminal13.Working Voltage: DC12V14.Output Current: 10A15.Rated load:10A 250VAC / 10A 125VAC10A 30VDC / 10A 28VDC16.Output:Normally open,Common,Normally closedWorking/output way:1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
For Arduino Kits accessory LDTR-WG0228 DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver
HLY Trading
£13.37
Please check the model, voltage, and other parameter.LDTR-WG0228 DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch ReceiverSpecification:1.Input Voltage: DC10-14V2.Standby Current: 90dBm6.Remote Control Distance: >100 meter(In open environment)7.Decoding Way: MCU Software decoding8.Can store the number of remote control:509.Support remote control type: Fixed code, learning code10.Channel: 1CH11.Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)12.Wiring Method:Fixed wiring terminal13.Working Voltage: DC12V14.Output Current: 10A15.Rated load:10A 250VAC / 10A 125VAC10A 30VDC / 10A 28VDC16.Output:Normally open,Common,Normally closedWorking/output way:1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relayDescription:1. press the lear
Arduino Accessory DIY tools, LDTR-WG0228 DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver
HUILIAN
£13.61
Please confirm model, voltage before ordering.please test the parts before install.LDTR-WG0228 DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch ReceiverSpecification:1.Input Voltage: DC10-14V2.Standby Current: 90dBm6.Remote Control Distance: >100 meter(In open environment)7.Decoding Way: MCU Software decoding8.Can store the number of remote control:509.Support remote control type: Fixed code, learning code10.Channel: 1CH11.Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)12.Wiring Method:Fixed wiring terminal13.Working Voltage: DC12V14.Output Current: 10A15.Rated load:10A 250VAC / 10A 125VAC10A 30VDC / 10A 28VDC16.Output:Normally open,Common,Normally closedWorking/output way:1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relayDescription:1. press the learning code .the indicator f
JDDRCASE LDTR-WG0228 DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver
JDDREU
£14.72
LDTR-WG0228 DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch ReceiverSpecification:1.Input Voltage: DC10-14V2.Standby Current: 90dBm6.Remote Control Distance: >100 meter(In open environment)7.Decoding Way: MCU Software decoding8.Can store the number of remote control:509.Support remote control type: Fixed code, learning code10.Channel: 1CH11.Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)12.Wiring Method:Fixed wiring terminal13.Working Voltage: DC12V14.Output Current: 10A15.Rated load:10A 250VAC / 10A 125VAC10A 30VDC / 10A 28VDC16.Output:Normally open,Common,Normally closedWorking/output way:1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relayDescription:1. press the learning code .the indicator flash ,loosen your finger ,press an
Cikuso 1CH Relay Shield V2 Version 2 for WEMOS D1 Mini ESP8266 WiFi Module for Arduino
Cikuso
£1.33
Cikuso is a brand which was registered. We are under Cikuso authorization to market the products under Cikuso trademark. We adhere to providing high-quality products and high-standard customer service all the time. 1CH Relay Shield V2 Version 2 for WEMOS D1 mini ESP8266 WiFi Module for ArduinoPackage Contents:2pcs x Normal pins 1pcs x Relay Shield Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
250A 10A DC12V 1CH Channel Relay Module Low Level Active for Arduino Home Smart PLC
Anddod
£15.99
Feature:Rated current: 10ARated voltage: 12VOutput contact maximum: 250A 10AThe IN1, IN2, IN3, IN4, IN5, and IN6 signal lines are active low.VCC, GND power input terminal, relay can be separately powered by relay power input terminal JD-VCC.Use:1. Support all microcontroller control2. Industrial field3. PLC control4. Home intelligent controlPackage includes:1 x 12V relay module
Sellify Electrical Equipments 5Pcs 5V 1Ch Low Level Trigger Relay Module One 1 Channel Relay Shield Board Dc Ac 220V for Arduino Pic Avr Dsp Arm Mcu
Generic
£13.88
5v 1ch low level trigger relay module one 1 channel relay shield board dc ac 220v for arduino pic avr dsp arm mcu features: 1. With isolation groove in control area and load area. 2. With power and relay action indication, bright when connect and go off when disconnects. 3. When there is a signal in signal input, public sidemon side will breakover. 4. It can be not only used as a microcontroller development board module, but also as a home appliance control. 5. It can not only control the dc or ac signal, but the 220v ac load. 6. With a permanent open and close vents contact. 7. It is convenient to connect with blue kf301 terminal access control cable. Specifications: 1. Vcc: power interface, 5v 2. Gnd: ground 3. In: control interface. Drive current at least 4ma 4. Com: control circuit ground, connect to gnd 5. Size: approx. 41 x 16 x 16mm/ 1.61 x 0.62 x 0.62'' 6. Weight: approx. 12g note: 1. High level flip-flops shows that there are trigger mode of the voltage between the signal input terminal and the ground. That is to say it is a way of short circuit trigger between signal input and vcc positive pole. 2. Low level flip-flops shows that there are voltage for ov trigger mode between the signal input terminal and the ground. In a word, it is a way of short circuit trigger between signal input and gnd negative pole. 3. Please allow 1-3mm differs due to manual measurement. 4. Due to the different display and different light, the picture may not reflect the actual color of the item. Thanks for your understanding. Package includes: 5 x 1 channel 5v relay module shield item specifics: model number: 5v 1ch low level trigger relay moduleusage: general purposevoltage: 5vis customized: yespower source: dcprotect feature: 1 channel relaytheory
3Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch
Yongse
£24.40
Use Learning coding, stable and reliableThe wireless signal can pass through walls, floors and doorsYou can turn on or turn off the receiver with transmitter (remote control) from any place within a reliable distanceOperating Voltage: DC12VMaximum Load: 10AOperating Frequency: 433MHZ (in set)Receiver Sensitivity: -100dBmEncoding Type: learning codeBoard Size: Approx. 5.3x3.1cm/ 2.09x1.22"Output Working Way: 1. Jog: Pressing one button is working. Loosing your finger on the same button is stop. (need one channel switch and one buttons remote control)2. Self-lock: Pressing one button for one time is working. Pressing the same button again is stop (need one channel switch and one buttons remote control)3. Inter-lock: Pressing one button is working. Pressing another button is stop (need one channel switch and 2 buttons remote control)4. Please notice that here is 1CH and 1 button wireless remote control. You can choose the self-lock or jog working/ output way, you better choose jog or self-lock, so pressing the button is open, and pressing again is close, or pressing is open, and loosing finger is closeLearning and Remove Method: 1. Press the learning code. The indicator from on to off, loosen your finger, press any button of the remote control, the indicator flash 2 times and off. It mean you learn it successfully2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless remote control3. Remove/ Clean: Press the learning button about 8 seconds, the indicator turn on to off, it means the information that you keep have been removed successfullyPackage Included: 3 x Learning Code Receiver3 x Remote Control
5Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch
Yongse
£36.80
The wireless signal can pass through walls, floors and doors You can turn on or turn off the receiver with transmitter (remote control) from any place within a reliable distance Operating Voltage: DC12V Maximum Load: 10A Operating Frequency: 433MHZ (in set) Receiver Sensitivity: -100dBm Encoding Type: learning code Board Size: Approx. 5.3x3.1cm/ 2.09x1.22" Output Working Way: 1. Jog: Pressing one button is working. Loosing your finger on the same button is stop. (need one channel switch and one buttons remote control) 2. Self-lock: Pressing one button for one time is working. Pressing the same button again is stop (need one channel switch and one buttons remote control) 3. Inter-lock: Pressing one button is working. Pressing another button is stop (need one channel switch and 2 buttons remote control) 4. Please notice that here is 1CH and 1 button wireless remote control. You can choose the self-lock or jog working/ output way, you better choose jog or self-lock, so pressing the button is open, and pressing again is close, or pressing is open, and loosing finger is close Learning and Remove Method: 1. Press the learning code. The indicator from on to off, loosen your finger, press any button of the remote control, the indicator flash 2 times and off. It mean you learn it successfully 2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless remote control 3. Remove/ Clean: Press the learning button about 8 seconds, the indicator turn on to off, it means the information that you keep have been removed successfully Package Included: 5 x Learning Code Receiver 5 x Remote Control
LaDicha 5Pcs DC 5V 1CH Relay Shield V2 Version 2 For WEMOS D1 Mini ESP8266 WiFi Module
LaDicha
£14.32
Description: New Relay Shield V2 for WEMOS D1 mini More infos is here! Package included: 5 x DC 5V 1CH Relay Shield V2 for WEMOS D1 mini
ILS. - 3 pieces DC 5V 1CH Relay Shield V2 Version 2 For D1 Mini ESP8266 WiFi Module
I LOVE SHOPPING
£9.20
Description:New Relay Shield V2 for WEMOS D1 miniMore infos ishere!Package included:3 x DC 5V 1CHRelay Shield V2for WEMOS D1 mini
F Fityle 3-32VDC 1CH 5A Relay Module High Level for Arduino Uno R3 PIC ARM DSP AC
F Fityle
£5.99
Find everything you want in Fityle! We will do our best to provide you with an excellent shopping experience on Amazon.Description: - Brand new and high quality - 1-Channel 3-32VDC Relay interface board - Equipped with high-current relay DC current - Load voltage: 24-380VDC - Widely used: PLC automation equipment control, industrial system control, Internet control, electronic hobbyist development test, all kinds of circuit modification, etc.Specification: - Material: Plastic - Color: As picture show - Size: Approx. 72x27x25mm/2.83x1.06x0.98inch - Hole Location Size: Approx. 24.5x69.5mm/0.96x2.74inch - Supply voltage: 3-32VDC - Quiescent current: 0mA - Maximum operating current: 12.5mA - Trigger mode: high level trigger; 1.5-32VDC Relay ON (ON), 0-0.5VDC relay off (OFF) - Load voltage: 24-380VDC - Load current: 5A - Module life: ≤ 10 million times - Switch the maximum frequency: 5KHZPackage Includes:1 piece Relay Module Board
SODIAL(R) 1CH Relay Shield V2 Version 2 for WEMOS D1 mini ESP8266 WiFi Module Arduino
SODIAL
£1.38
* SODIAL is a registered trademark. ONLY Authorized seller of SODIAL can sell under SODIAL listings.Our products will enhance your experience to unparalleled inspiration. SODIAL(R) 1CH Relay Shield V2 Version 2 for WEMOS D1 mini ESP8266 WiFi Module for ArduinoPackage Contents:2pcs x Normal pins 1pcs x Relay Shield Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
ILS. - DC 5V 1CH Relay Shield V2 Version 2 For D1 Mini ESP8266 WiFi Module
I LOVE SHOPPING
£4.94
Description:New Relay Shield V2 for WEMOS D1 miniMore infos is here!Package included:1 x DC 5V 1CHRelay Shield V2for WEMOS D1 mini